|
Suitable for cars with twin reflector headlights. Can be fitted to base models with single reflector (H4) headlights, but wiring will need to be adapted. For safety reasons headlights should be fitted and adjusted by a professional
|
|
|
Wiring up angel eyes & LED sidelights: Connect all loose white wires from the resistor boxes to the loose white wire at the large connector in headlight wiring harness; insulate joint. Repeat for loose black wires.
|
|
|
If the original lights have electric height adjustment the motors must be transferred to the new lights. Undo four screws & remove rear panel so manual adjustment pivot can be removed to fit the motor; motor wiring is provided inside panel.
|
|
|
Suitable for cars with twin reflector headlights. Can be fitted to base models with single reflector (H4) headlights, but wiring will need to be adapted. For safety reasons headlights should be fitted and adjusted by a professional.
|
|
|
Wiring up angel eyes & LED sidelights (if fitted): Connect all loose black wires to one of the THICK black wires in the headlight harness; insulate joint. Connect all loose red wires to the white wire in the harness; insulate joint.
|
|
|
Wiring up angel eyes & LED sidelights (if fitted): Connect all loose black wires to one of the THICK black wires in the harness; insulate joint. Connect all loose red wires to the white wire in the harness; insulate joint. Wiring u
|
|
|
Can be fitted to all models, however the automatic levelling (height adjustment) function may not operate if the motor cannot be transferred to these lamps. Automatic levelling is not a legal/MOT requirement.
|
|
|
VAUXHALL Astra 4 (98-04) Projector Head Lights - Chrome Angel Eyes (RHD Only) | Performance Lights.co.uk
Wiring up angel eyes & LED sidelights (if fitted): Connect all loose black & white wires from resistor boxes to the negative & positive side of the car’s sidelight bulbholders respectively; insulate joints.
|
|
|
If the original lights have electric height adjustment the motors must be removed and transferred to the new lights. The pivots for manual adjustment must be removed to fit the motors.
|
|
|
Wiring up angel eyes & LED sidelights: Connect all loose white wires from the resistor boxes to the loose white wire at the large connector in headlight wiring harness; insulate joint. Repeat for loose black wires.
|
|
|
Wiring up angel eyes & LED sidelights (if fitted): Connect all loose black wires to one of the THICK black wires in the headlight harness; insulate joint. Connect all loose red wires to the white wire in the harness; insulate joint.
|
|
|
Wiring up angel eyes & LED sidelights: Connect all loose white wires from the resistor boxes to the loose white wire at the large connector in headlight wiring harness; insulate joint. Repeat for loose black wires.
|
|
|
If the original lights have electric height adjustment the motors must be transferred to the new lights. Loosen two clips & remove rear panel so manual adjustment pivot can be removed to fit the motors; motor wiring is provided inside panel.
|
|
|
Suitable as a replacement for cars without electric height adjustment. Can be fitted to models with electric height adjustment, but this function will be lost - this will not cause an MOT failure as it is not a legal requirement.
|
|
|
Wiring up angel eyes & LED sidelights (if fitted): Connect all loose black wires to one of the THICK black wires in the headlight harness; insulate joint. Connect all loose red wires to the white wire in the harness; insulate joint.
|
|
|
Wiring up angel eyes & LED sidelights (if fitted): Connect all loose black & white wires from resistor boxes to the negative & positive side of the car’s sidelight bulbholders respectively; insulate joints.
|
|
|
SUBARU Impreza (97-00) Projector Head Lights - Chrome Angel Eyes (RHD Only) | Performance Lights.co.uk
Wiring up angel eyes & LED sidelights (if fitted): Connect all loose black & white wires from resistor boxes to the negative & positive side of the car’s sidelight bulbholders respectively; insulate joints.
|
|
|
Can be fitted to all models, however the automatic levelling (height adjustment) function may not operate if the motor cannot be transferred to these lamps. Automatic levelling is not a legal/MOT requirement.
|
|
|
Wiring up angel eyes & LED sidelights: Connect all loose black & white wires from the base of the headlight to the negative & positive side of the car’s sidelight bulbholders respectively; insulate joints.
|
|
|
Wiring up angel eyes & LED sidelights (if fitted): Connect all loose black & red wires from the base of the headlight to the negative & positive side of the car’s sidelight bulbholders respectively; insulate joints.
|
|
|
Wiring up angel eyes & LED sidelights (if fitted): Connect all loose black & white wires from resistor boxes to the negative & positive side of the car’s sidelight bulbholders respectively; insulate joints.
|
|
|
If the original lights have electric height adjustment the motors must be transferred to the new lights. Undo five screws & remove rear panel so manual adjustment pivot can be removed to fit the motor; motor wiring is provided inside panel.
|
|
|
Wiring up angel eyes & LED sidelights: Connect all loose white wires from the resistor boxes to the loose white wire at the large connector in headlight wiring harness; insulate joint. Repeat for loose black wires.
|
|
|
CITROEN C3 (02-) Projector Head Lights - Black Angel Eyes (RHD Only) | Performance Lights.co.uk
Wiring up angel eyes & LED sidelights (if fitted): Connect all loose black wires to one of the THICK black wires in the headlight harness; insulate joint. Connect all loose red wires to the white wire in the harness; insulate joint.
|
|
|
Wiring up angel eyes & LED sidelights: Connect all loose white wires from the resistor boxes to the loose white wire at the large connector in headlight wiring harness; insulate joint. Repeat for loose black wires.
|
|
(UK)
